|
Products for open and closed loop control of hydraulic drives
|
|
Software for parametering of our digital control modules and calculation of hydraulic cylinder drive
|
|
Software
|
Description
|
Documentation
|
|
WPC-300
Version 2.95
|
Start up software to adjust and optimize our digital power amplifier and control modules.
- Table orientated input
- Monitor for process data
- Oscilloscope
- Loading and saving of parameters
|
WPC-300.ZIP (2.95)
Docu:
WPC-300-PDF
INFO
Driver (USB-SO)
|
|
WPC-300
Version 3.0
|
New Version of our Start-Up program (Beta Version). All new options will be supported up module software version *20.
- Improved table oriented input
- Improved Oscilloscope, up to four channels
- Improved monitor
- New Remote control function
- Increased communication speed
|
WPC-300.ZIP (Version 3.0 beta)
|
|
Cylinder
|
Simple calculation of cylinder drives and the control system parameter for our positioning modules.
|
CYLINDER
|
|
Command signal generation modules
|
|
Module
|
Description
|
Documentation
|
|
DSG-111
|
Digital command signal module with 16 programmable command signals and ramps. Optional: integrated power amplifier.
|
DSG-111A (rev 8)
Appendix:
Power stage PEXT3
|
|
MOT-114
|
Power amplifier with motor potentiometer function. The output current is controlled by two digital input signals for increasing and reducing the current. The speed
can be adjusted by different ramp times.
|
On request
|
|
DSS-161
|
Command signal module for switching of four external analogue command signals (potentiometers).
|
DSS-161-10 rev 8
|
|
DSG-164
|
Command signal module with four internal adjustable command values. Adjustable via potentiometer.
|
DSG-164 rev 8
|
|
MMA-165
|
Analogue adjustment of MIN and MAX values. This module can be used in combination with our digital control modules. Simple (without a Notebook) adjustment of the max
value or min value with potentiometers.
Two independent channels are implemented.
|
On request
|
|
LS-3A
|
Special version used for electronic load sensing control.
|
On request
|
|
Position and Axis control modules
|
|
Module
|
Description
|
Documentation
|
|
POS-121
|
Simple positioning module with analogue command and feedback signal.
The used control structure is: stroke dependent deceleration.
Expandable with integrated power amplifier.
|
POS-121 doku (rev 8)
Appendix:
Power stage PEXT3
|
|
POS-122
|
General position control module with eight selectable command positions and speeds.
The control structure can be switched over per command: 1. stroke dependent deceleration or 2.
NC-control mode with following error control.
|
POS-122 doku (rev. 8)
|
|
POS-123
|
General position control module with analogue command position and command velocity input. External controllable speed profiles are
possible.
The control structure can be switched over per command: 1. stroke dependent deceleration or 2. NC-control mode with following error control.
Available with integrated power stage.
|
POS-123 doku (rev. 8)
Appendix:
Power stage PEXT3
|
|
POS-123SSI
|
General position control module with analogue command position and command velocity input. External controllable speed profiles are possible.
The control structure can be switched over per command: 1. stroke dependent deceleration or 2. NC-control mode with following error control.
Position feedback with digital SSI interface
|
POS-123SSI (rev. 8)
|
|
POS-123PDP
|
General position control module with integrated Profibus DP interface. Sensor feedback analogue or SSI.
Expanded internal functions.
HIGH/LOW or LOW/HIGH speed profiles.
|
POS-123PDP rev 11
GSDDatei
|
|
PPC-125PDP
|
Control of hydraulic axis in position and pressure/force control. The functions of the POS-123PDP are expanded by a typical pressure control function with one or two pressure
sensors.
|
PPC-125 doku (rev. 8)
GSDDatei
|
|
POS-127
|
Position control module for high speed double stroke movement. This unit is optimized for: oscillation drives, cutting and punching.
|
POS-127 doku (rev. 8)
Appendix:
Power stage PEXT3
|
|
POS-128
|
Positioning control module as an alternative solution for high and low speed movements. The position is measured by an analogue position sensor, no limit switches are
required. All positions and speeds are adjustable. Independent from the viscosity.
|
POS-128 doku (rev 8)
POS-128SSI (rev 8)
Appendix:
Power stage PEXT3
|
|
General PID compensator, pressure control and speed control modules
|
|
Module
|
Description
|
Documentation
|
|
PID-131
|
General PID controller.
Versions with Profibus DP or CAN are available.
|
PID-131A (rev 8)
|
|
PQ-132
|
PQ control module for hydraulic pressure or force control.
|
PQ-132A (rev 8)
|
|
PQ-132PDP
|
PQ control module for hydraulic pressure or force control (with integrated Profibus DP interface).
|
PQ-132PDP Profibus (rev 8)
GSD Datei
|
|
MDR-133
|
Pressure control module for proportional pressure control and relieve valves. High accuracy (0,01%), simple handling, scalable inputs and a good dynamic
behaviour support the use in valve and pump controlled applications.
Version with Profibus PD (MDR-133PDP) is available.
|
MDR-133A (rev 8)
Appendix:
Power stage PEXT3
|
|
MDR-137
|
Low cost pressure control module. Inexpensive, small housing and integrated power stage for proportional valves
emphasize the general character of this module.
|
MDR-137 (rev 8)
|
|
SCU-138
|
Low cost speed control module. Inexpensive, small housing and integrated power stage for proportional valves emphasize the general character of this
module. Digital pulse sensors up to 5000 Hz can be used.
|
SCU-138
|
|
Synchronization control
|
|
Module
|
Description
|
Documentation
|
|
CSC-151
|
Synchronization control module for bypass control (in conjunction with any type of flow divider). Useful for a stable and accurate
synchronization of two to four axes. Different hydraulic concepts are supported.
|
CSC-151A doku (rev8)
CSC-151SSI (rev 8)
Appendix:
Power stage PEXT3
|
|
CSC-152
|
Synchronization and position control module for general synchronization tasks where each axis is controlled by one proportional valve.
Analogue controlled (analogue sensors) up to four axes (up to two axes in master/master mode), with digital sensors (SSI interface) up to
24 (30) axes. The axes are linked via CAN bus in high speed mode. Optionally with Profibus DP interface.
|
CSC-152 doku (rev. 8)
CSC-152SSIC_DE-rev. 8 (Profibus)
Appendix:
Power stage PEXT3
GSD-Datei
|
|
Pump control modules
|
|
Module
|
Description
|
Dokumentation / Download
|
|
PQP-171
|
Closed loop displacement control of servo pumps.
|
On request
|
|
PQP-172
|
Special pump displacement control via the pressure valve.
|
On request
|
|
PQP-173
|
Closed loop displacement, pressure and power control with one control valve (pressure valve).
|
On request
|
|
PQP-175
|
Closed loop displacement, pressure and power control. Displacement and pressure are
controlled by two independent valves.
|
PQP-175PDP rev 8 (Profibusversion)
|
|
PQP-176
|
Closed loop displacement, pressure and power control with one control valve
(directional valve). Depending on the requirements simple proportional valves or control valves (servo valves) can be
used.
|
PQP-176 doku (rev 8)
|
|
PQP-177
|
Pump control (displacement, pressure and power) for closed hydraulic circuits.
|
on Request
|
|
Power amplifier for proportional valves
|
|
Module
|
Description
|
Documentation
|
|
PAM-191
|
Power amplifier for pressure or throttle valves. Internally full digital
controlled. Adjustment via potentiometer, power supply 12 V or 24 V.
Versions with different PWM frequencies are available.
|
PAM-191-30 rev 8
|
|
PAM-192
|
Power amplifier for directional valves. Internally full digital controlled.
Adjustment via potentiometer, power supply 12 V or 24 V. This new version will replace the older PAM-192, PAM-193
and PAM-194
Versions with different PWM frequencies are available.
|
PAM-192-30 rev 9
|
|
PAM-195
|
Digital power amplifier to control one proportional directional valve.
This power amplifier is adjustable via PC software WPC-300 or the hand held terminal HHT-302. Different
programmable functions support the general use.
Also available with CAN or Profibus Interface
.
|
PAM-195-rev 8
|
|
PAM-196
|
Digital power amplifier to control two independent proportional pressure
or throttle valves. This power amplifier is adjustable via PC software WPC-300 or the hand held terminal
HHT-302..
Also available with CAN or Profibus Interface
.
|
PAM-196-rev 8
|
|
PAM-197
|
Power amplifier with 8 digital selectable command values. Useful for
high and low speed movement or digital selectable pressures.
|
PAM-197-rev 8
|
|
PAM-198
|
Power amplifier for proportional valves with spool position feedback
(EATON, DUPLOMATOC, PARKER, ...)
|
New version (documentation on request)
|
|
PAM-205
|
Two channel power amplifier for throttle and pressure valves.
|
PAM-205 rev. 2
|
|
SV-200
|
Servo amplifier with an adjustable
current range of 10 to 200 mA (in 10 mA steps). Optional with a current range up to 300 mA.
|
SV-200 rev 9
|
|
DSG-111P
|
Digital command signal module for general use with
integrated power amplifier.
|
DSG-111A (rev 8)
Appendix:
Power stage PEXT3
|
